AEMâ€™s 380lph High Flow, High Pressure Fuel Pump is capable of supporting over 1,200 HP normally aspirated and a whopping 860 HP at 30 psi boost!* It flows 380 lph (100 gph) at 43 PSI, 340 lph (90 gph) at 73 PSI, and 270 lph (71 gph) at 120 PSI. Complete flow curves from 35 to 120 PSI and current draw vs. fuel pressure charts are available in the specs tab.
The AEM 380lph High Flow Fuel Pump is designed for use with gasoline. Alcohol fuels can be used, but pump life will be diminished. The inlet thread is a -10 AN female ORB (O-ring port fitting) and the discharge is a female -6 AN ORB (O-ring port fitting).
A male -6 to -8 AN discharge fitting with integral high pressure check valve, terminal nuts, terminal boots and installation instructions are included. Optional accessories that are sold separately include a -10 ORB fitting inlet pre-filter (for use with in-tank installations), and both -8 and -6 discharge adapters without integral check valves. Accessory fittings are hard anodized.
Designed for high output naturally aspirated and forced induction EFI vehicles
Popular â€œ044 Styleâ€ physical configuration but with AN inlet & discharge port connections
Maintains very high flow even at boosted fuel pressures; 340 lph @ 73 PSI (30 psi boost)
Installs externally or in-tank
Each pump individually tested to flow minimum of 380lph (100gph) @ 43 PSI
For gasoline vehicles (pump life will be diminished when used with alcohol fuels)
Kit includes fuel pump, -6 to -8 male AN discharge fitting with check valve, terminal nuts & boots, instructions
Optional -10 ORB fitting pre-filter, -6 and -8 discharge adapters without the integral check valves
Optional Inline High Flow Fuel Pump Accessories
50-200-06: -6AN Discharge Fitting
50-200-08: -6AN to -8AN Discharge Fitting with Integral Check Valve
50-200-10: -10AN Inlet Port Fitting
50-200-11: -10AN Inlet Port Filter
50-200-86: -6AN to -8AN Discharge Fitting
*Power rating given using gasoline and assuming a base fuel pressure of 43 PSI, 13.5v at the pump, 6.2 lbs/gal with a BSFC of 0.65. Boost fuel pressure is assumed to be the base pressure of 43 PSI + boost pressure. Flow capability for horsepower support is ultimately dependent on fuel hose diameter, and system electrical voltage and amperage capabilities.
Weight:Â 35.8oz (1015 grams)
Outside Diameter:Â 60mm OD
External Materials:Â Black plated steel with laser etching, with zamac discharge end cap
Inlet Fitting:Â -10AN 7/8"-14 Female
Outlet Fitting:Â -6AN 9/16"-18 Female
PRV Activation:Â 150 PSI
Impeller Design:Â Roller vane with ceramic end plate
Connector Terminal:Â 6mm stud positive, 5mm stud negative
Min Voltage Input:Â 10 volts
Max Voltage Input:Â 18 volts
Current Draw (40 psi):Â 9.73 amps no check valve, 10.68 amps with check valve (13.5v)
Current Draw (120 psi):Â 16.07 amps no check valve, 17.13 amps with check valve (13.5v)
Fuse:Â 25 amps (13.5v), 30 amps (13.5v) MAX
* Power rating given at 43 PSI, 13.5v at the pump with a BSFC of .5. Flow capability for horsepower support is ultimately dependent on fuel hose diameter, and system electrical voltage and amperage capabilities.